LINEAR BUFFER ™ Straight Line Buffing Machine

$202.95

WHY YOU NEED IT

Saves time, labor and sore arms and shoulders. Use with ALUMABUFF™ to quickly and easily remove stains, streaks and white oxidation from Aluminum pontoons and boats. Buff a 22′ pontoon in less than 60 minutes. For more information on how to clean and restore aluminum, visit the ALUMABUFF™ catalog page.

Two models available: One for flat surfaces on aluminum boats, One for curved surfaces on pontoon boats.

*Prices do not include GST

SKU 01280 Category

Description

AURORA MARINE POWER POINT PROFESSIONAL QUALITY LINEAR BUFFER

Use With ALUMABUFF™ to Quickly Remove Stains, Streaks and white oxidation from Aluminum. LINEAR BUFFER™ Saves Time, Labor & Sore Muscles.Can you really buff all the stains, streaks and oxidation from a 22 ft. pontoon in as little as 60 minutes? Yes you can, with ALUMABUFF™ and a LINEAR BUFFER™.LINEAR BUFFERS move back and forth in a linear motion so it works parallel to the grain. It cleans and polishes without cutting across the grain, unlike rotary buffers that are designed to be used only on smooth non directional surfaces, such as automotive paint or fiberglass. When used with ALUMABUFF™ and the special ALUMABUFF PADS™ it quickly and easily removes the stains, streaks and oxidation, restoring the original silver finish without cutting and grinding away the top layer of aluminum like old fashioned rubbing compound and metal polish. For more information on how to clean aluminum, visit the ALUMABUFF™ catalog page.

AURORA MARINE offers two versions of their POWER POINT PROFESSIONAL QUALITY LINEAR BUFFER. Both are constructed with heavy duty parts to withstand the continuous and rigorous demand and pressure required to buff aluminum pontoons and boats. Both are made with Stainless Steel buffing plates to prevent deformation when pressure is applied and to prevent corrosion. Both have double thick foam buffing blocks to better maintain contact with the aluminum surface.

MODEL 01280A: Has a flat buffing block, ideally suited for flat surfaces such as aluminum boats.
MODEL 01280P: Has a concave buffing block to maintain full contact with the curved surface of aluminum pontoons.

BE SURE TO SELECT THE RIGHT MODEL. Maintaining full contact with the aluminum surface while buffing will insure better results, less time and effort buffing and fewer replacement ALUMABUFF PADS™.

The POWER POINT LINEAR BUFFER™ is an air operated buffing machine that requires compressed air from a compressor. It requires 90 psi, but can run on slightly less. Most portable compressors with a 3 to 5 gal tank and 100 psi, or larger, are adequate. The POWER POINT LINEAR BUFFER™ has a 15 ¾” buffing block that operates back and forth in a linear motion, moving approximately 1 inch at up to 3,000 strokes per minute, free speed, and slower under pressure. It has dual cylinders to eliminate dead spots and stalling and operates at low noise and vibration levels.

The back and forth linear motion is important as it follows the grain to clean the stains and streaks without cutting across the grain which removes a layer of aluminum. With a little practice controlling the speed and pressure, you should be able to restore your aluminum pontoon or boat in one pass. Heavily oxidized aluminum may require repetition until the aluminum is bright and shiny again.

The POWER POINT LINEAR BUFFER™ uses a Velcro Hook Strap mounted to the pad assembly to accommodate the special ALUMABUFF PADS™ that are designed for optimum efficiency when used with ALUMABUFF™. The pads with the special micro fibers, cleans the surface as well as getting into the recesses to clean them as well. ALUMABUFF™ contains HYPEXINE™, a special leaching agent that brings the stains to the surface so they can be easily and quickly removed. Removing streaks, stains, tarnish and oxidation from aluminum is fast, easy and much cleaner with this system. It can reduce the time it takes to restore your aluminum by 90%.

The POWER POINT LINEAR BUFFER™ uses a Velcro Hook Strap mounted to the pad assembly to accommodate the special ALUMABUFF PADS™ that are designed for optimum efficiency when used with ALUMABUFF™. The pads with the special micro fibers, cleans the surface plus it gets into the recesses to clean them as well. ALUMABUFF™ contains HYPEXINE™, a special leaching agent that brings the stains to the surface so they can be easily and quickly removed. Removing streaks, stains, tarnish and oxidation from aluminum is fast, easy and much cleaner with this system. It can reduce the time it takes to restore your aluminum by 90%. ALUMABUFF™ is water based and free rinsing so it’s not necessary to degrease the surface prior to applying ALUMETRON™ clear coat. Just rinse it clean with a pressure washer or garden hose and brush.

Why You’ll Love It!
  • Quickly & Easily Removes Stains, Streaks & Oxidation.
  • Saves Time & Labor.
  • Cleans & Polishes without cutting across the grain.
  • Restores Aluminum to its original Silver Finish.

 

A. Features & Functions

• Dual cylinder, 251 mm (1″) stroke, 3000SPM (Max.)
• Stainless Steel Buffing Plate
• Positive locking clamps
• Double Thick foam buffing block
• Low noise and vibration level
• Velcro Loop for quick change of Buffing Pad
• No dead point design for comfortable operation
• Use with ALUMABUFF PADS™ for buffing aluminum
• Pontoon Model has concave Buffing Block for maximum contact

B. Air Supply

1. Make sure that the air compressor being used for the air tool operation supplies the correct output (CFM)
2. Make sure the Trigger is in the “OFF” position when connecting the tool to the air supply.
3. Use normal 90psi (or ranging from 6.0 to 8.0kg) air pressure while running the tool.
4. Drain the air tank daily.
5. Clean the air inlet filter cartridge weekly.
6. Line pressure should be increased accordingly to make up for extra long air hoses(usually over 25 ft/8 meters). The minimum hose diameter should be 1/4″.
7. Use proper hoses and fittings.
8. Keep hoses awayf rom the heat, oil and sharp edges. Check hoses for wear before individual use. Make certain that all connections are secure.

C. Safety Instructions

1. Approved eye protector must be worn at all times. If necessary, 0. ear protector & gloves should be used.
2. Always keep good balance of body & footing. Secure work with 0. clamps if necessary, so both hands can be free to operate the tool.
3. Be sure all clothing is tight to prevent entanglement with 0. 0. running tools. Remove jewelry and watch for safety purpose.
4. Be sure that working area is clear of foreign objects and that no people are within immediate access to tool operation scope. The working place shall be well ventilated.
5. Disconnect the air hose before changing or adjusting Pads or Loop.
6. Be sure that Tool is in “OFF” position before connecting to the air hose.
7. Disconnect the tool when it is not in use.
8. Never carry tool by the hose.

D. Maintenance and Lubrication

1. If you are not using an airline oiler, lubricate the air motor by applying 4 to 5 drops of SAE #10 lubricant or sewing machine oil in the air inlet and in the side oil port, prior to 1st use and prior to each use thereafter. Do not use Detergent Oil.
2. Oiling in the air inlet is necessary every 1 hour of continuous operation.
3. After operation, take off the airhose and pour 4 or 5 drops of #60 spindle oil into the air inlet, then connect the hose again to run the tool for a few seconds. This will prolong the tool life.
4. Clean air inlet filter cartridge on the airline weekly.

FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID THE WARRANTY

E. Warnings

1. Never use the tool in potentially explosive atmospheres.
2. Keep your body in well balanced position and always wear gloves to reduce the risk of crushing caused by torque between the reaction bar and work piece.
3. Unexpected tool movement due to reaction forces may cause injuries.
4. Prevent long hair or loose clothing from drawing in while operating the tool.
5. The Noise (sound pressure level) at the workplace may exceed the normal standard —usually 85dB(A). In this case, quality ear protector should be used.
6. Slip/Trip/Fall is a major cause of serious injury or even death. Be aware of excess hose left on your walking way or on the working surface.
7. Continuous operation and bad working condition can injure hands. If hands become numb or aches or if a serious symptom occurs, operator shall see a doctor immediately.

F. General Trouble Shooting

* Troubles:
– Tool does not run
– The motor stops
– Starts automatically when connected to compressed air
– Torque reduces
– Abnormal vibrating
– Housing heats up

* Causes:
– Not sufficient Air Aupply
– Speed controller/switch is defective
– Dirt gets into motor
– Starting trigger malfunction
– Air leakage at the inlet or in line
– O-ring(s) worn out or out of position
– Lack of Lubrication

 

LINEAR BUFFER™

    • Catalog No: 01280A / 01280P
    • Individual Unit: 1
    • Shipping Weight: 8 lb
    • Case Volume: 1 X 8 lb
    • Case Weight: 8 lb (3.6 kg)
    • Case Dimensions: 18″L x 7.75″W x 5.50″H
    • Pad Size: 15.75″ x 2.75″

TECHNICAL DATA :

    • Free Speed: 3,000 rpm
    • Buffing Pad: 2.5″ X 15.75″ (63.5×400 mm)
    • Air Inlet: 1/4″ BSP or NPT
    • Air Hose (ID): 3/8″
    • Avg. Air Consumption: 8 CFM (226 l/min)
    • Air Pressure: 90 psi – 6.2 Bar

Useful Links

Reviews

There are no reviews yet.

Be the first to review “LINEAR BUFFER ™ Straight Line Buffing Machine”

Your email address will not be published. Required fields are marked *

You're viewing: LINEAR BUFFER ™ Straight Line Buffing Machine $202.95
Add to cart
X
Shopping cart close